#Keypad deadbolt how to
#Keypad deadbolt manual

You have now successfully removed the Schlage deadbolt from your door. Remove the strike plate and the bolt and keep them alongside the other lock components.

Usually, the strike plate is connected to the bolt of the door and comes off together. Unscrew the faceplate that is sitting flush against the edge of the door. Step 6: Remove The Schlage Deadbolt Strike Plate If you plan to use the same lock again, you must ensure that no individual component of the lock is lost or damaged. Carefully and gently pull the inner and outer portions of the lock apart to remove the Schlage deadbolt cylinder components and set them aside. The two pieces of the Schlage deadbolt may be removed once all of the screws have been removed. Step 5: Remove The Schlage Deadbolt Cylinder Insert the flat blade beneath the cap and lift the lever towards the middle of the screw. If the screws on your deadbolts are covered by a screw cap, use a tiny, thin flat-bladed screwdriver. Whether your deadbolt screws are visible after removing the faceplate or were not concealed below the plate, in either case, you can remove the screws using a Phillips head screwdriver. Simply find the little cutout around the rim, enter the tiny flat-headed screwdriver, and carefully lift the plate away from the lock. Schlage lock plates are normally kept in place by friction and have a tiny notch at the edge. Step 3: Remove The Schlage Deadbolt FaceplateĪfter removing the latch from the lock, you can easily remove the ornamental plate. Once removed, keep the thumb latch and any pins in a secure location in case you need them later. Some Schlage locks may include a plastic or metal pin on the shaft of the latch handle that may be used to remove the latch handle. When you feel the thumb latch release, remove it and set it away. Put any sharp-edged object inside the hole, such as an awl, a hairpin, or a paper clip that has been straightened, and press gently. Look for a tiny hole in the shaft that connects the thumb latch to the rest of the deadbolt lock to remove it. If your deadbolt’s screws are not visible because they are hidden under the faceplate, you must first remove the thumb latch. However, to access the hidden screws of your Schlage deadbolt, follow the instructions given below. If you have visible screws on your deadbolt, jump to step 4. The following tools will be required to remove a Schlage lock from your door.

#Keypad deadbolt how to

Step 1: Get the Required Toolsīefore learning how to remove a Schlage lock, make sure you are all set and well-prepared for the process by gathering the necessary equipment. This section of the article will provide you with both. The removal of Schlage deadbolts locks is not a challenging task if you have the right tools in place and a step-by-step guide for instructions. To read more about single-cylinder and double-cylinder deadbolts, click here. But since this is not a fixed rule for all the deadbolts, it is recommended to observe the lock for the hidden or visible screws physically. In contrast, a double-cylinder deadbolt has a keyhole on both sides and has the screws concealed below a plate. Usually, a single cylinder with a thumb turn on the inner side of the door has visible screws mounted on the thumb turn. Hence, some deadbolts may have visible screws, while others may have them concealed under a plate for aesthetic purposes or as an added security measure. Since Schlage manufactures a number of deadbolt models, some Schlage deadbolts differ from others. So, without any delay, let’s get to the point! Does Your Schlage Deadbolt Have Hidden Or Visible Screws?

#Keypad deadbolt manual

But not anymore! This article will take you through stepwise instructions about removing the Schlage deadbolt, both manual and keypad, from your door. If you are here, I am sure you, too, struggled a bit. While many users find the installation of Schlage locks quite user-friendly, a few users struggle with finding a detailed guide about removing a Schlage deadbolt, as only a little literature is available on the internet. Honestly, I trust them so much that not only I but even my parents and sister have them installed at their homes. They manufacture locksets for almost any application and offer a wide range of residential deadbolts. Schlage is a well-known manufacturer of deadbolt locks in the United States. To remove a Schlage keypad lock, you disconnect all the cables from the deadbolt side after removing the lock cylinder.

While some Schlage lock models may have screws visible to the users, others may have them concealed under a plate for aesthetic or security purposes.Removing a Schlage deadbolt is a task that you can accomplish easily by accessing the mounting screws that hold the deadbolt together to the door.